Middag manne,
30mm Scope Tube beteken dit 30mm ringe sal reg pas? Rede ek vra ek het 30mm scope tube vir my 6-24x50mm scope en het warne 30mm ringe wat volgens warne se instruksie met 25lbs vas gemaak moet word ek het ook die Wheeler FAT wrench wat ek verstel het tot met 25lbs maar voel dat dit nogal kwaai druk as ek dit probeer vas skroef met daai poundage (lbs) wil net seker maak ek draai nie die skroefies van die warne mounts te styf om my scope se tube nie?
Groete,
30mm Scope Tube beteken dit 30mm ringe sal reg pas?
-
Finder20
- Sr. Member
- Posts: 466
- Joined: Tue Jun 27, 2017 8:30 am
30mm Scope Tube beteken dit 30mm ringe sal reg pas?
Veteran - British Army - Brigade Recce Force
22LR CZ 452 Lux Modified
6.5 Creedmoor Howa Varmint APW Carbon X
308 Howa Varmint KRG Whiskey-3
300 PRC Howa Varmint APW Carbon X
375 H&H Bergara B14 Timber
9mm Para Glock 17 GEN 5
22LR CZ 452 Lux Modified
6.5 Creedmoor Howa Varmint APW Carbon X
308 Howa Varmint KRG Whiskey-3
300 PRC Howa Varmint APW Carbon X
375 H&H Bergara B14 Timber
9mm Para Glock 17 GEN 5
-
Malan123
- Hero Member
- Posts: 2128
- Joined: Sat Oct 29, 2016 4:07 pm
Re: 30mm Scope Tube beteken dit 30mm ringe sal reg pas?
30mm ringe moet pas ja. Wees versigtig met die warne ringe. Draai bietjie vas onder en dan weer bietjie vas bo.
-
Finder20
- Sr. Member
- Posts: 466
- Joined: Tue Jun 27, 2017 8:30 am
Re: 30mm Scope Tube beteken dit 30mm ringe sal reg pas?
Dankie Malan 
Veteran - British Army - Brigade Recce Force
22LR CZ 452 Lux Modified
6.5 Creedmoor Howa Varmint APW Carbon X
308 Howa Varmint KRG Whiskey-3
300 PRC Howa Varmint APW Carbon X
375 H&H Bergara B14 Timber
9mm Para Glock 17 GEN 5
22LR CZ 452 Lux Modified
6.5 Creedmoor Howa Varmint APW Carbon X
308 Howa Varmint KRG Whiskey-3
300 PRC Howa Varmint APW Carbon X
375 H&H Bergara B14 Timber
9mm Para Glock 17 GEN 5
-
ruaanb
- Hero Member
- Posts: 5557
- Joined: Thu Aug 14, 2014 10:29 am
Re: 30mm Scope Tube beteken dit 30mm ringe sal reg pas?
Ek het hierdie so 'n ruk terug op 'n oorsese forum gekry en dit gesave.
Ek plaas dit hier met erkenning aan die betrokke persoon.
"The question has been asked on several occasions
what the torque for bedding screws and scope bases
should be so I though this might be helpfull.
"NOTE" These are based on full engagement of threads.
Wood, Fiberglass or Synthetic stock without bedding pillars-
40 inch-lbs.
Wood, Fiberglass or Synthetic stock with bedding pillars -
up to 65 inch-lbs.
Hard-use service-type rifles in synthetic with pillars-
up to 65 inch-lbs.
Law enforcement & military rifles are 65 inch-lbs on each
of the guard screws.
On rifles with three guard screws the middle screw should
be only slightly tightened.
Scope base screws 30 inch-lbs "MAX"
Windage screws 30-40 inch-lbs "MAX"
Scope ring screws (Aluminum Rings) 10-15 inch-lbs "MAX"
Scope ring screws (Steel Rings) 15-20 inch-lbs "MAX"
Note' If scope base and ring Screws have less than 5 threads
of engagement they should be replaced with longer ones.
Barrel to receiver Torque 35 ft/lbs minimum to 95 ft/lbs Max.
If an anti seize compound is used instead of a light oil use 65
ft/lbs max to prevent over torquing.
I hope this will help
J E CUSTOM
"
Ek plaas dit hier met erkenning aan die betrokke persoon.
"The question has been asked on several occasions
what the torque for bedding screws and scope bases
should be so I though this might be helpfull.
"NOTE" These are based on full engagement of threads.
Wood, Fiberglass or Synthetic stock without bedding pillars-
40 inch-lbs.
Wood, Fiberglass or Synthetic stock with bedding pillars -
up to 65 inch-lbs.
Hard-use service-type rifles in synthetic with pillars-
up to 65 inch-lbs.
Law enforcement & military rifles are 65 inch-lbs on each
of the guard screws.
On rifles with three guard screws the middle screw should
be only slightly tightened.
Scope base screws 30 inch-lbs "MAX"
Windage screws 30-40 inch-lbs "MAX"
Scope ring screws (Aluminum Rings) 10-15 inch-lbs "MAX"
Scope ring screws (Steel Rings) 15-20 inch-lbs "MAX"
Note' If scope base and ring Screws have less than 5 threads
of engagement they should be replaced with longer ones.
Barrel to receiver Torque 35 ft/lbs minimum to 95 ft/lbs Max.
If an anti seize compound is used instead of a light oil use 65
ft/lbs max to prevent over torquing.
I hope this will help
J E CUSTOM
"
