Ad blocker detected: Our website is made possible by displaying online advertisements to our visitors. Please consider supporting us by disabling your ad blocker on our website.
Die proses is maar net om die reticle op n sekere vergroting by jou spesifieke lading in n .308 te "fine tune". Oor dit sfp scope is, sal afmik met reticle verskil op verskillende vergrotings. Die kruishaar moet steeds nie skuif as jy vergroting verstel nie.
_____________________
Gamo CFX .177
Howa/Krieger 6XC
Howa .243AI
Howa .300 WM
Musgrave .308
Was toevallig vandag langs 'n ou by Durbanville skietbaan wat selfde probleem het. Nuwe Zeiss met RZ1000 kruishaar, wat se zero skuif saam met vergroting.
Jean Marais wrote:Nou net die op hul usermanual raakgelees. Dis hoe die scope werk.
7. RAPID-Z[REGISTERED SIGN] 1000 Sight-In Instructions
The Rapid-Z[REGISTERED SIGN] 1000 reticle is unique in that it is the only Rapid-Z[REGISTERED SIGN] reticle that is engineered
around a specific caliber and bullet type. This reticle is designed to be used with the .308 Win
load in either 168 or 175 gr. Match loads. Other calibers like the .325 WSM and .338 Federal also
work but they are the exception to the rule.
This reticle is unique in another way in that is the center crosshair is “zero” for 500 yards. In order
to zero the reticle correctly please observe the following instructions.
1. Obtain the Optimum Power Setting form the Zeiss Ballistic Calculator. When you are completed
with the calculator also take note of the Zero at 100 Yards Data provided in inches. This
number will allow you to actually zero the reticle at 100 yards for 500 yards.
2. Place the firearm in a steady gun vice or sandbag on the rifle range using safe practices.
3. With the scope on your Optimum Power Setting; place the 500 yard center crosshair in the
middle of the bullseye. Note the 100 yard bar will be positioned about 12” above the center
of the target bullseye. Make certain your target paper is large enough to accommodate this
difference.
4. Fire a round with the center crosshair in the bullseye. You want the bullet to cut a hole in the
paper target exactly where the 100 yard bar intersection is. Adjust the riflescope windage and
elevation as required.
5. The distance between the bullet hole (100 yard bar) and the bullseye (500 yard crosshair)
should be the value calculated on the Zeiss Ballistic Calculator for Zero at 100 Yards. This value
is normally is between 11”- 13” depending upon your individual ballistic variables.
6. Remember 12” at 100 yards is equal to 60” at 500 yards. This is about how much a .308 Win
Match load drops at that distance. The key is to get this calculated spacing correct between
the 100 yard bar and the 500 yard bar so you can easily sight and shoot at longer range with
the holdover bars while on the Optimum Power Setting. You can fine tune your magnification
setting up or down to adjust from this zero point if required.
Jean die handleiding sê slegs vir jou hoe om jou second focal plane se vergroting te gebruik wanneer jy jou Scope op 100m wil inskiet ipv op 500m want die margin of error is net te groot op 500m.
Jou middelpunt kan nie wil skuif nie. Wat gebeur as daar verskriklik baie Mirage is en jy nie op 25 vergroting kan skiet nie, moet jy maar net huistoe gaan en op 'n ander dag weer probeer.
Indien wel het zeiss glad nie gedink nie of my kop is plat!
Dit is hoe Zeiss se RZ1000 werk, ek het self een van hulle gehaad en het ook nie verstaan hoekom hy dit doen nie. Toe vra ek vir die mense van Zeiss toe se hulle dis hoe die RZ1000 werk. Dit is stupid, ek het hom toe verkoop.
