Page 1 of 1

Turrets en kruishare praat hulle een taal ?

Posted: Wed Mar 07, 2012 7:44 pm
by Marc
Manne

Die ding het kop uitgesteek in ander post oor lang afstand skiet. Ek wil nie graag daai post hijack nie so het besluit om hopelik hier opinies en goeie raad te ontvang. Glo baie gaan ietsie hier leer.

Wat is die voor en nadele van scopes met Mildot kruishaar en wat in MOA stel vs scopes met Mildot kruishare wat in milliradian stel en dan natuurlik ook anders om.

Goed soos MOA kruise wat in MOA stel, ens. Ek dink min van ons besef hoeveel makliker die lewe kan wees as mens net verstaan hoe die turrets en die kruishare met mekaar behoort te praat  ???

Ludwig en Wouter het die houtjies gepak, ek hoop hulle kan vir ons vuurmaak ook. Ander manne kan asseblief ook die lig help aanhou.

Dankie by voorbaat vir die insette manne  ;)

Mooiloop
Marc

Re: Turrets en kruishare praat hulle een taal ?

Posted: Thu Mar 08, 2012 6:56 am
by Beyers
1 milrad is amper 4 MOA
Op 100m is 1milrad 100mm
Op 100m is 1 MOA 29mm x 4 =116mm dus 16 clicks met 'n 1/4 MOA scope
Om 1 Milrad te stel sou ek 14 Clicks stel

Re: Turrets en kruishare praat hulle een taal ?

Posted: Thu Mar 08, 2012 9:21 am
by Marc
Ludwig wrote: Marc, ek is bevrees hiermee het jy (of was dit ek?  ;D  ) dalk nou 'n blik wurms oopgemaak.

Ludwig

Jou blik wurms wat oor my kom seil het  ;D

Dankie vir die "kort" maar kragtige verduideliking. Ek lees altyd van die goeters in boeke en forums, maar hou net so 10% van die inligting in. Ek is besig om ,n .243 op te bou vir langafstand skoote. {300m en verder, sal sien waar ons opeindig} So nou is die tyd om regtig te begin oplet innie klas  ;D

Jy weet nou al ek het die Mark 4 8.5-25x50mm LR/T M1 gekoop, hy het MOA turets en ek het die Tactical Milling kruis gevat {TMR}. Asseblieftog se net die kombinasie gaan werk  ??? hulle s? nie of die kruis in MOA gekalibreer is nie  ???

Is daar enige goei plekke om te gaan oplees oor die onderwerp, iewers waar meer feite gegee word en minder ander goed tussen in wat die tor laat afval. Kom ons begin satdig want ek kruip nog eers.

BAIE DANKIE  ;)

Mooiloop
Marc

Re: Turrets en kruishare praat hulle een taal ?

Posted: Thu Mar 08, 2012 9:39 am
by Marc
Eina

Lyk my ek gaan vir die begin 'n Range finder moet aanskaf  ;) tot ek die ding onder die knie gekry het  ;D

Re: Turrets en kruishare praat hulle een taal ?

Posted: Thu Mar 08, 2012 10:17 am
by Beyers

Re: Turrets en kruishare praat hulle een taal ?

Posted: Thu Mar 08, 2012 6:42 pm
by Marc
Beyers

Dankie ek leer mooi  ;)

Ludwig

Daai wurms kruip nou die hele w?reld vol, maar ek is glad nie spyt nie ! Ek wens net ek het bietjie meer huiswerk gedoen voor die koopie. Tog gaan ek reg kom, gaan net of 'n tabel moet opstel of soos jy s?: prakties gaan toets waar om te vat om die kombinasie te maak werk  ;D

As ek dink ek weet darem ietsie, gaan ek saam ges?ls  ;)

Hoop ander manne val ook in  ???

Mooiloop
Marc

Re: Turrets en kruishare praat hulle een taal ?

Posted: Fri Mar 09, 2012 10:39 am
by Marc
Man ek is bly dit is stil by die werk, vandag werk daai arme tor oortyd  ;D ;D ;D

Ek gaan 'n paar interesante gesprekke hier copy, alle eer aan die skrywers.

Introduction
The first thing you've got to know is what a centimeter (CM) is, basically one third of an inch or the lenght of a fingernail. A meter (M) is 100 centimeters. For our purposes, a milliradian or MIL for short, is similar in concept to MOA, 1 MIL = 10CM @ 100M or 20CM @ 200M or 30 CM @ 300M, ect.


1 Milling the target
The "1M Target" is the consistant measurement of an adult male human. The leg bones are responsible for the majority of human hight variation and thus are excluded from measurment for maximum accuracy. The "1M Target" is ranged by measuring crotch to crown, against a scope reticle which is divided into increments of 1 MIL or less. This reading is compared to the targets actual size via an equation. A quick way to double check your ranging is to measure the shoulder blades of the target. At .5M it should be half the MIL reading of "1M Target". The nice thing about using the "1M Target" is that it makes the equation simple, the "known height" parameter can be eliminated because it has no multiplactive value.

So........

Known size of target (meters) x 1000
________________________________ = Range to target (Meters)

Observed size of target (MILS)


Becomes........


________1000________________ = Range to target (Meters)

Observed size of target (MILS)


Now the math can be calculated in the operators head. Observed target size = 5 MILS => Range = (1000 / 5) = 200M
4.00 MIL => 250M
3.00 MIL => 330M
2.25 MIL => 440M
2.00 MIL => 500M
1.75 MIL => 570M


2 Milling range reference points
One of the advantages of MIL based reticles is you can range any object in the kill zone before a target is detected, provided it's dimensions are known. The simplest way to exploit this feature is to maintain a list of known size, of objects likely to be encountered. Purchase a Mildot Master with additional metric slide and let it calculate the range (Meters) for you, again double check range by width measurement and mildot master calculation.
If there is contradiction between the primary hight and width milling results, it is good practice to re-MIL on sub-structures within an object, e.g doors and windows on buildings or vehicles. If the object is being viewed from a significant horizontal or vertical angle, priority should be given to the non angled reading. This is superior to simply halving the difference. When you have your range confirmed, consult your metric dope sheet and write down the adjustment required for this target distance reference point in your range card. This permits rapid engagement of a target that is difficult to measure, as long as they are located near one of the reference points.


3 Milling with the reticle
Lets establish some constraints, reticle ranging is only effective inside 600M on targets no smaller than 1M. This requires the ability to range down to the nearest 0.25 MIL. Engaging in excess of 600M requires the use of a GPS, map overlay or LRF.

Hash reticles are more intuitive, just align the scale and count the hash marks. However, there are a lot of conventional Mil Dot scopes out there. This section will cover how to use them with the minimum of skill. The example will be based on the USMC reticle pattern. Each dot on the crosshair is 0.25 MIL in diameter and 1 MIL apart from the next dot, hence the gap between each dot is 0.75 MIL. The intersection of the crosshairs represent the centre of an implied dot. This data translates to convenient reference points. The principle is the same for the US ARMY pattern, though the values are different.


1.00 MIL= The base of Dot A to base of Dot B
1.25 MIL= The base of Dot A to top of Dot B
1.75 MIL= The top of Dot A to the base of Dot C
2.00 MIL= The base of Dot A to the base of Dot C
2.25 MIL= The base of Dot A to top of Dot C
2.75 MIL= The top of Dot A to the base of Dot D
3.00 MIL= The base of Dot A to the base of Dot D

Note that these readings correspond to the readings in section 1. The only guesstimation involves increments of .5 MIL, for example, if the target is larger than 1.25 MIL but smaller than 1.75 MIL then we can deduce that it is 1.5 MIL.


4 Holdoff with the reticle
Holdoff is effective out to 500M on exposed targets not less than 1M high. It can be used for rapid adjustment, gusting wind, multiple ranges, corrected fire, ect. Longer ranges are given priority when calibrating the holdoff zero. In dope sheets made easy, we cover how to express the dope in MILS. Enter 200yds in the "zero range" field. Adjust the zero value until 500M has an integer adjustment value in MILS, so it aligns with the reticle. This is your "hold off zero". Draw the hold points on a reticle diagram with 300M & 400M moved to the closest dot. Mark 10MPH windage holdoff points on the diagram too. The hold off zero changes accordance to variations in enviormental conditions/air density and should be noted on each dope sheet. However the rifle is physically zeroed at 100 yds, this is your primary zero as it not affected by enviros.


5 Practice
Air rifle range:
When training on an air rifle, milling an orange 15MM~40MM target, out to a range of 30M, develops and maintains range estimation skill. You need to accurately estimate to within 2M to hit the target. The metric Mildot Master slide will calculate the range to reduced targets by shifting the decimal point. 1CM = 10MM, so if you want to calculate the range of a 40MM target, select 40CM and remove a zero from the range result.

Actual range:
You need a way of verifying your ability to estimate range, while LRF's are convenient they are sensitive to lighting and enviormental conditions. A useful example like the CRF 1200 will cost $700. Another method is to use a GPS handset to plot each target as a waypoint. This can be done when planting targets or walking through an area you intend to practice on. UTM maps and tools facilitate the remote entry of a target's GPS coordinates. This can also be used operationally, as a secondary method of passive ranging.


6 Useful scope features
Illuminated reticle
Allows a scope to function in low light, some variable scopes can operate in moonlight conditions. Back lighting the reticle with a mini chem-light is another option.

Parallax focus
Most sniper scopes with magnification in excess of 9X have this, the knob is usually located opposite the windage turret. Use the eyepiece focus to set the scope to your vision, bringing the reticle into focus. Use the main parallax knob to bring the sight picture into focus for various ranges. As a final check move your head sidways, back and forth. If the sight picture and reticle move as one then procede with ranging / engaging.
A scope with parallax focus can be used to read heat mirage, in order to estimate wind direction and speed. Scopes that focus down to at least 10M can also be used on air rifles.

FFP variable magnification
Variable magnification makes the scope more flexible. FFP lets the operator use the reticle for ranging and/or hold off at any magnification setting. One less setting for the operator to worry about.

Metric turrets
If the turret's adjustment increments are in CM (0.1 MIL), then the operator's dope sheet can be expressed in MILS rather than MOA. The operator can employ either clicks or reticle hold off without converting from MOA to MILS. This is a very fast system.

BDC turrets
This is another way to ignore MOA clicks and/or dope sheets. A BDC is just a series of reference numbers on the turret to indicate the range adjustment, 3 = 300M, 4 = 400M, ect. They can be written on wrapped masking tape or ingraved. The only downside is that the operator is locked into one specific round, where as a dope sheet can be switched in a matter of seconds.

Zero Stop
This is a device that locks out negative adjustment past zero and prevents the operator getting lost. The photo below shows an improvised stop made from copper pipe and cut to the correct lenght to prevent turret travel. Marking the zero level with a paint pencil is another option.

Re: Turrets en kruishare praat hulle een taal ?

Posted: Fri Mar 09, 2012 10:51 am
by Marc
Lots of people are asking these days about getting into long range shooting, and what scope and reticle they should get.

Disclaimer: I am not an "expert", but shoot my fair share of long range and steel matches with a bolt gun. After talking with a lot of people that do the same I think the following is some good basic information.

Hopefully some of the other experienced long range scoped rifle shooters will chime in with their information.

Opinions are varied. Mostly it comes down to what one is comfortable using, and what you have to know and remember to get the most out of the reticle you use. These days it goes without saying that if the option to have the knobs and the reticle both MOA or both MIL, it's better to do so. Not all scope manufacturers offer that option. It's not a deal killer, just nicer to have.

There are literally dozens of reticle choices depending on who you get a scope from. Most are variations on a theme and offer more or less detail depending on the needs of the shooter. When it comes to MOA reticles pretty much the only choice is lines. With MIL you can have either lines or dots. Lines are exactly that, whereas dots are circles and ovals of specific size, but centered at the same place as a MIL line would be.

Typical reticles.

The Nightforce NP-R1, a MOA reticle.

Image

The Nightforce MLR, a MIL reticle.

Image

Since by volume Leupold is probably the largest, their TMR, a MIL reticle.

Image

With MIL dots there are 2 types. The Army dot, and the USMC dot.

Army

Image

USMC

Image

Whether MIL or MOA, the reticle is not used just for ranging, but also for "holding over/under" for elevation, or "holding off" for windage instead of dialing the knobs. This is most useful when engaging targets at different ranges in rapid succession, or when making multiple quick shots in changing wind conditions.

Some people will ask, "Which reticle gives better accuracy, or the ability to make a finer compensation for adjustment?"

Well, when it comes to MILs, if you ask the Army and Marines, you will get 2 different answers because they each calculate it differently. The Army says a MIL is 3.53 inches at 100 yards, the Marines say it's 3.6" at 100 yards. When it comes to MOA there are also 2 different answers because some are made in Shooters MOA, which is 1" at 100 yards, and some are made in True MOA, which is 1.047 inches at 100 yards.

Image

But since most people can't make really fast rapid calculations in their head in the field, and often times in competition (or on the battle field) time does not allow one the luxury of pulling out a calculator, we'll go with the Army MIL definition and Shooter MOA because it makes math easy.

I made the chart below (I'm pretty sure I got it right, and if I didn't I know someone will correct me) so you can see what what the different gradations are in inches at various distances.

On most scopes with MOA lines the lines will have gradations of .5 and 1 moa, MIL line scopes will have them in .2, .25, .5 and 1 mil. This is not taking into account the thickness of the lines themselves, just the main horizontal and vertical lines. Mil dots are a different animal and take a lot more practice to use.


__________________
Rob Thomas - Match Director NCPPRC Tactical Long Range Match

Match Director Sac Valley Vintage Military Rifle Long Range Match

Re: Turrets en kruishare praat hulle een taal ?

Posted: Fri Mar 09, 2012 10:53 am
by Marc
However, with the above quoted comment I either disagree or misunderstand you. An actual MOA at 100yds is 1.047" and if Leupold M1 dials are closer to 1" at 100 yds (I am assuming you are correct here as I do not know), lets just call them an actual 1" at 100yds for the sake of math (and it may prove the point better since being close to 1" versus being exactly one inch doesn't show as much of a difference).

Ok, so if the M1 does dial 1" per every 100yds (as opposed to a true 1.047"), that is better for me since my example earlier in this thread (4" being 1/2moa at 800yds) was accounting for 1" per 100yds rather than true precise 1.047". Since I think in 1" per 100yds, I am happy to find out that Leupold adjusts in 1" per 100yds... makes it kinda handy.

The next question is likely why I don't use true MOA (1.047") and instead use 1" per 100yds. The easy answer for me now is that is what Leupold scopes adjust in. The usual answer we give is a bit better though. Lets say you and I went to the range and I figured 1" per 100yd and you did the actual 1.047" per 100yds. How far off would our numbers be from each other? One might assume that since I am not using the true number that I would be way off. Well, at 1000yds, my 1moa is 10" and your true 1moa is 10.47". Less than half of an inch difference at 1000yds. That is barely wider than the width of the bullet, .308".

So risking being off .47" at 1000yds (which I can not adjust for on my Leupold scope M1, M2, or M3 turrets nor can I even shoot a group that would notice .47" at 1000yds and the slightest breeze will affect more) I calculate 1moa as 1" at 100yds rather than 1.047" at 100yds.

My example earlier... I can quickly see that 4" at 800yds is 1/2 moa and adjust for that on my M2 dials. If I used the actual 1.047", I would have to use my calculator to see that 1/2 moa is actually 4.188" at 800 yds. This information takes me longer to get, and I can't even adjust for that let alone shoot well enough to have .188" make a difference. Figuring 4.188" is not useful for me.. 4" is (not only is it easier to picture, it is the adjustment I can actually make on the scope).

So using 1" per 100yds in my book is much better than using 1.047" per 100yds for the practical reasons I set forth above as well as the fact that I now know that Leupold adjusts in that unit of measurement.

Did I explain that well? It seems a bit garbled as I look back at it. Let me know what you think about why I use 1" per 100 and ignore the 1.047" (gasps heard across the internet that I ignore the more precise options) per 100yds.

OK - I'll explain the math behind my comment.

Let's say that you know from your ballistic program that the drop of your 175 SMK launched at that 1000 yard target at 2600 fps is 416 inches.

If you think your scope dials in true MOA, i.e., 1.047 inches at 100 yards, you will dial up:

416/10.47 = 39.73

However, if the scopes is actually dialing in 1.000 inches at 100 yards, you will dial up:

416 / 10 = 41.6

The difference is 1.87 MOA - and 1.87 MOA at 1000 yards is about 18 inches.

I discovered that when I went from a Leupold 3.5-10X40M3, which dials true MOA, to a 6.5-20X50M1, which dials in 1 inch per hundred yard (IPHY), and found a 20 inch elevation difference.

So, I calibrated the clicks on the M1. Everyone M1 I have checked since is 1 IPHY.

And that's why I advocate that people check the actual value of the adjustments on their scopes.

To people who are NRA square-range shooters, who get sighters shooting at a target, it doesn't matter. But to people who shoot UKD targets, and need first- or second-round hits, it matters.

Re: Turrets en kruishare praat hulle een taal ?

Posted: Fri Mar 09, 2012 10:59 am
by Marc
Hierdie is ook 'n goeie een, net baie informasie om te copy. Lees maar gerus  ;)

http://www.shootingvoodoo.com/index.php ... d_reticle/

Re: Turrets en kruishare praat hulle een taal ?

Posted: Fri Mar 09, 2012 12:30 pm
by the kid
Sjoe maar nou is ek eers deurmekaar ???

Wonder of julle slim ouens my kan help, net in teorie, Ek weet ek sal dit moet toets op my eie wapen.

Ek het 'n mildot scope met ffp reticle, hy het daai turrets wat jy stel vir die afstand wat jy op skiet.

Nou ek was nog altyd onder die indruk dat 4 clicks op 100m 1 duim is, ek sien nou dit is nie heeltemal waar nie. maar soos die afstande verander verander die hoeveelheid clicks wat jy moet stel vir dieselfde effek.

Nou gestel dit is my ballistic table.

100 Gr. Nosler Ballistic Tip 3350 / 2491 +1.08 @100YRD/ 3086 / 2115 +0.00 @200YRD / 2835 / 1784 -5.41 @300YRD/ 2595 / 1495 -16.02@400YRD / 2368 / 1245 -32.79 /500YRD 2156 / 1032

As die scope op 100YRD gezero word, hoeveel clicks sal mens op die verskye afstande stel om die geweer gezero te hou?

100yrd +1.08
200yrd +0.00
300yrd -5.41
400yrd -16.02
500yrd -32.79

Of is dit nie so eenvoudig nie?

wat ek verstaan het was as dit 4 clicks op 100yrd is dan is dit net 2 clicks op 200 yrd, is dit reg? maar dan wat van 300,400,en 500 hoeveel clicks is daar nodig?


Jammer as ek nou iets belagliks gevra het, maar my wiskunde kan net die maklike somme maak :D

Re: Turrets en kruishare praat hulle een taal ?

Posted: Fri Mar 09, 2012 1:20 pm
by the kid
OK, weet jy, vir my vermoe is dit naby genoeg ek sal daarmee speel.

Die scope se specs se: 1 click = 1/4 in @100yrd or 7.3mm @100m

kan jy dalk net vir my se hoe werk mens uit hoeveel 1 click op die verskillende afstande is?

Re: Turrets en kruishare praat hulle een taal ?

Posted: Fri Mar 09, 2012 1:25 pm
by Marc
Kid

Loer hierdie links van Beyers, jy gaan nie spyt wees nie  ;) en dit gaan jou vrae mooi beantwoord.

Re: Turrets en kruishare praat hulle een taal ?

Posted: Fri Mar 09, 2012 3:02 pm
by Marc
Ludwig wrote: Ditto Marc, daai videos verduidelik dit mooi

Onthou om nie hierdie gegewens van 1/4" per click op 100y na meter net so oor te dra nie. 1/4" per click op 100y is nie gelyk aan 'n 1/4" per click op 100m nie. Passop daarvoor  ;)
Goeie punt Ludwig, het hele tyd gedink ek moet seker maak on in yarde te skat en nie meters nie  ;) Dankie vir die boompie wat jy geplant het, hy groei te pragtig  ;D