Page 1 of 1
Using S355 in the .260 Rem
Posted: Mon Apr 20, 2015 9:03 am
by offroad
Morning guys,
Any guidence or advice of using S355 in the .260 Rem?
I am loading 43gr of S365 with 140gr Berger VLD's and noticed during load testing of OAL, that some of the loads were heavily compressed and I was wondering if S355 would reduce this.
Perhaps a question that the QL guys may be able to answer?
Re: Using S355 in the .260 Rem
Posted: Wed Apr 22, 2015 8:20 am
by offroad
Sjoe - no one?
Re: Using S355 in the .260 Rem
Posted: Wed Apr 22, 2015 8:51 am
by Giepie
I don't use a 260 (yet), but if the case is filled past 106% I would go for S355. If the powder pushes the bullet back out, it's to much.
Re: Using S355 in the .260 Rem
Posted: Wed Apr 22, 2015 8:56 pm
by JPS
Hi Offroad, we have looked at S355 but had much better rests with S365.
I would suggest looking at a faster lot of S365 like lot 74 or there about, we load our bullets one kne so our col are quite long and therefore do not have the issue with running out of cas capacity and for the same reason S355 did not work as we did not have adequate case fill.
Regards
Jan
Re: Using S355 in the .260 Rem
Posted: Wed Apr 22, 2015 9:55 pm
by Rudie
JPS wrote:Hi Offroad, we have looked at S355 but had much better rests with S365.
I would suggest looking at a faster lot of S365 like lot 74 or there about, we load our bullets one kne so our col are quite long and therefore do not have the issue with running out of cas capacity and for the same reason S355 did not work as we did not have adequate case fill.
Regards
Jan
These findings mirrors my experience with the 260rem. I put some S365 lot 74 aside to only use in the 260. The lighter bullets in the 120gr range works well with S355
Re: Using S355 in the .260 Rem
Posted: Wed Apr 22, 2015 10:56 pm
by Kalahari
offroad, sorry, i don't want to hijack your post.
Rudie, JPS, if you go even lighter than 120gr, say 107 or 108 gr (or even 95gr vmax) would s355 work, or should one stay with s365? I am looking for a good reason (excuse) to not use s365 in any of my rifles.
Re: Using S355 in the .260 Rem
Posted: Thu Apr 23, 2015 12:05 am
by JPS
Kalahari,
Jammer maar ek Het nog glad nie die ligte koeels geskiet nie so kan ongelukkig nie help met die vraag nie. Skiet die swaarder koeels vir Lang afstand.
Groete
Jan
Re: Using S355 in the .260 Rem
Posted: Thu Apr 23, 2015 7:28 am
by offroad
Thanks to all for the replies.
Rudie wrote:
These findings mirrors my experience with the 260rem. I put some S365 lot 74 aside to only use in the 260. The lighter bullets in the 120gr range works well with S355
Rudie can you share the loads are you using with S355 and the 120gr bullets? I picked up some Nosler 123gr bullets the other day (I couldn't find any VLD's) so I am looking for start loads using S355.
Re: Using S355 in the .260 Rem
Posted: Thu Apr 23, 2015 7:38 am
by tripodmvr
With Nosler 123CC start with 38gr S355. If you fire 3 shots over the chrony and record group the QL can do some magic. Speed should be around 2700fps. I would suggest COL 1mm from the lands.
Re: Using S355 in the .260 Rem
Posted: Thu Apr 23, 2015 8:13 am
by offroad
Thanks tripodmvr - much appreciated.
Due to way this thread has developed maybe it should really be moved to the Herlaai Data section?
Re: Using S355 in the .260 Rem
Posted: Thu Apr 23, 2015 8:23 am
by Arnold
S355 is the only way to go with the lighter 107/8gr bullets imo.